A few years ago, I was in the market for a new table saw. My decision was between a sliding table saw or a SawStop table saw (you can read more about my decision process in the three articles titled Why a Sliding Table Saw with a Scoring Blade?, Why Not a SawStop? and Benefits of a Sliding Table Saw – links at the bottom of this article). In June 2010, I drove down to Grizzly’s showroom in Bellingham, Washington and had a good look at the G0623X 10″ Sliding Table Saw before ordering one for delivery. By the way, the sticker price on this saw was right around the $3,000 mark. I have had the saw for four years and have been really happy with my purchase. The saw was larger than my contractor’s saw with a 30″ fence, but the sliding table saw used space so well that I barely noticed a difference.
What’s So Great?
The saw was nicely made and easy to assemble and adjust. Blade changes were a snap with the arbor lock pin.
The sliding table has proven to be very useful for large crosscuts as well as making straight, accurate cuts in both normally- and oddly-shaped parts. On the occasion when I’ve had to work with sheet goods, the 60″ sliding table has been a clear advantage for material support (no infeed or outfeed support required for most cuts). The five horsepower motor had plenty of power to rip thick hardwoods or cut dadoes and the scoring blade produced perfect cuts on the bottom of fine plywood and melamine. When done with the scoring blade, I simply removed it from the arbor, which was much easier than lowering it and resetting it for the next time. When dealing with many small parts such as when I made a batch of Time Warp Tool Works Moulding Planes, I was again able to benefit from the sliding table. I piled the uncut parts on one end of the sliding table, made the required cuts using the middle section of the table, then stacked the cut parts on the other end of the table itself. As I worked, all parts remained on the table which traveled back and forth as a whole, so parts were never in the way or out of arm’s reach at any point. There were two T-slots in the top and one in the edge of the sliding table that allowed the attachment of the outrigger, mitre gauge, and other accessories such as a hold down or handle. They were also useful for storing pencils and rulers (and sawdust!). Because the sliding table extended to within a fraction of an inch of the blade, I could clamp even a small part in place for cutting, then push it through the blade without even being near the part or the blade. Furthermore, the long sliding table encouraged the user to stand to the left of the blade – out of the way of the path of kickback. And yes, the saw has a riving knife too. The outrigger was clamped to the table and could be slid forwards or backwards as desired. A pivoting arm attached to the back of the saw cabinet supported the far end of the outrigger and a threaded adjustment allowed it to be levelled. The crosscut fence offered ample support for almost all cuts, and a pair of flip stops made breaking down stock efficient. The fence could be mounted at either the front or back of the outrigger, and a set of adjustable flip stops ensured that the fence could be set square time and time again. The blade tilt and height were adjusted with two well-made hand wheels with folding handles and centre knobs for locking their setting. They felt nice and worked well.
The mitre scale on the outrigger was a decal with fat lines, so I couldn’t rely on it for accurate angles. Instead, I would use a bevel gauge to set the crosscut fence to the blade. Some of the higher-end sliding table saws had some useful features that this saw did not have, such as the option to lock the sliding table all the way forward for loading, or a switch on the sliding table. Dust collection was fair. There was an additional provision for collecting dust in the blade guard, which I elected to not use. One thing I did find out was that if sawdust was allowed to accumulate between the blade access door and the blade shroud, it prevented the door from closing properly and contacting the microswitch which allowed the saw to run. The saw came with a mitre gauge which could be clamped to the sliding table. I always preferred to use the larger crosscut fence and the only time that I used the mitre gauge was if I had removed the outrigger for some reason. This wasn’t really a negative, just a “do I really need this?” accessory.
Modifications and Additions
When the saw arrived in my shop, I couldn’t figure out how to lower the riving knife below the crown of the blade, so I ground some metal off of the back top of the riving knife to allow me to perform non-through cuts. My shop was quite narrow, and the crosscut fence was long, with an extension to allow even wider crosscuts. I decided to cut the aluminum crosscut fence to end where the outrigger ends. When I needed to make cuts between 37 and 74 inches, I could use the extension. (When I cut off the end of the crosscut fence, I also removed the tapped hole for the knob that locks the extension in place, so I needed to drill and tap another hole.) The extension came with a ramped stock support, but since I never cut stock long or flimsy enough to warrant it, I removed it. The crosscut fence was secured to the outrigger with a long, threaded bolt and was tedious to wind in and out when I wanted to install or remove the fence. I solved that by making a simple locking device with a lever-action clamp that fit into a T-slot in the bottom of the crosscut fence. I was glad that I bought a cam-action hold down with the saw. The saw didn’t come with the hold down and they were not sold separately. However, the hold down was included with another saw which has the same size T-slots (1-1/4 x 1/2 inch) so I ordered all the parts and assembled it myself. It wan’t cheap, but it sure was worth the price! Additional resources about this saw are provided in the links below. If you have any other questions, please feel free to submit it in the comments box at the bottom of this article.
Related Articles From My Blog:
- Why a Sliding Table Saw with a Scoring Blade?
- Cam-Action Hold-Down for Grizzly G0623X Sliding Table Saw
- Why Not a SawStop?
- Benefits of a Sliding Table Saw
- G0623X 10″ Sliding Table Saw on Grizzly.com
- My New Sliding Table Saw
- Moving & Assembly of the Sliding Table Saw
- More Adjustments on the Sliding Table Saw
- Straight Line Ripping on a Sliding Table Saw